Sutter Instruments P-97

Flaming/Brown Micropipette Puller

The Sutter P-97 Flaming/Brown type micropipette puller is ideal for fabricating micropipettes, patch pipettes and microinjection needles. While retaining many of the features of earlier models, the Sutter P-97 offers improvements in mechanical, electronic and software design. The result is better control of the pulling process and a higher degree of reproducibility. The Sutter P-97 combines a proven mechanical system with a sophisticated, programmable microprocessor controller. This programmable control of the pulling parameters allows the investigator to design application specific pipettes from a wide range of glass compositions and sizes.

A number of other features have been incorporated in the design of the Sutter P-97. Most apparent is the environmental chamber which surrounds the heating filament. This environmental chamber is designed to minimize the effect of changing humidity on the reproducibility of pulled pipettes. A 25% increase in power over the Sutter P-87 allows for the use of larger heating filaments, larger diameter glass and multi-barreled glass. The metal jaws that clamp the heating filament have also been redesigned to minimize heat retention. A gas delivery mode switch provides for extended cooling for large diameter and multi-barreled glass. A spring-loaded clamping mechanism has been added for easier loading of glass. A vacuum fluorescent display has been added that allows easy viewing.

Software improvements on the Sutter P-97 include a display of the total heat-on time to assist in program development and troubleshooting. Up to 100 programs can now be written and stored in memory, which makes the P-97 suitable for multiple users. These programs can now be write-protected, adding security to prevent programs from being changed or altered inadvertently. The display shows the last date and time the program was written or edited. In addition, the air pressure is included as a programmable parameter.

The Sutter P-97 contains a ramp test to overcome the difficulties of program adjustment when a new filament is installed or to help characterize a new glass and filament combination. This test allows for the rapid adjustment of heat values in established programs and provides estimates for establishing heat settings when using new sizes or compositions of glass capillaries. As with all Sutter instruments, the electronics have been carefully designed to maximize noise rejection.

The Sutter Instrument P-97 Flaming/Brown type micropipette puller is ideal for fabricating micropipettes, patch pipettes and microinjection needles. While retaining many of the features of earlier models, the Sutter Instrument P-97 offers improvements in mechanical, electronic and software design. The result is better control of the pulling process and a higher degree of reproducibility. The Sutter Instrument P-97 combines a proven mechanical system with a sophisticated, programmable microprocessor controller. This programmable control of the pulling parameters allows the investigator to design application specific pipettes from a wide range of glass compositions and sizes.

Features

  • Environmental chamber
  • Programmable air pressure
  • Memory storage for up to 100 programs
  • Write protection and date stamp for each program
  • Two symmetrical pipettes with each pull
  • Two cooling modes: time and delay
  • Preprogrammed sample programs for intracellular and patch pipettes. Special programming on request
  • Ramp test – self test for establishing program heat settings when a new filament or glass is introduced
  • Vacuum fluorescent display
  • Constant current power supply for filament and pull solenoid
  • Looping pull cycle for fabrication of patch type micropipettes
  • Self-contained air supply with filtration system and humidity control
  • Consistent and reliable electrodes with tip diameters less than 0.1µm
  • Control over the time and pressure at which the air is delivered
  • Optimized velocity sensing circuit for maximized sensitivity and reproducibility
  • Quality control, SEM photograph of a tip pulled with each puller; criterion is tip measurement less than 0.1µm and typically is ~0.06µm
Sutter Instruments P-97

TECHNICAL SPECIFICATIONS

Dimensions
21in x 16in x 12in | 53cm x 40.6cm x 30cm

Weight
50 lbs | 23 kg

Electrical
115/230 volts
50/60 Hertz power line

(281) 579-0342

How can we help? Call us: +1 (281) 579-0342 or 281-755-4332
Got a question? Need a quote? Want a demo or trial? Email to rdm@meyerinst.com or fill out the form below and we will be in contact shortly.

    Your Full Name (required)

    Telephone Number

    Your Email (required)

    What can we help you with?

    Can you be more specific?